Personalizing pencils in batches with the Pencil Engraving Jig

Difficulty: medium. Time: 30 minutes for the jig, then minutes per batch. Methods: laser engraving, UV printing, or 3D printing the jig.

Engraving one pencil is easy; engraving forty, straight and identically positioned, is a fixturing problem. This tool solves it by generating two things that match exactly: a jig sheet with slots that cradle each cylindrical item, and the text artwork pre-positioned over each slot. Cut the jig once, drop in the pencils, run the engrave pass, swap in the next batch.

Presets cover Pencil, Drumstick, Chopstick, and Knitting Needle, and every dimension stays editable, so any roughly cylindrical blank works: pens, dowels, wand blanks, paintbrush handles.

Example of Pencil Engraving Jig
On this page (6)
  1. 1. Pick a preset and measure
  2. 2. Set the text
  3. 3. Export
  4. Laser Engraving
  5. UV Printing
  6. 3D Printing

What you need

  • Laser: 3 mm laser-grade plywood or MDF for the jig sheet, plus your pencils or blanks
  • UV printing: a flatbed UV printer; print the jig PNG template or use the laser-cut jig as the fixture
  • 3D printing: any FDM printer if you would rather print the jig than cut it
  • 3M tape to lock the jig to the laser bed so batch after batch stays registered

1. Pick a preset and measure

Open the tool and choose the Pencil, Drumstick, Chopstick, or Knitting Needle preset, then verify Diameter and Length against your actual blanks with calipers. Under Layout, choose Custom Count for a set number of slots or Fill Sheet to pack as many as fit your Sheet Width and Sheet Height. Gap Between Slots and Border Margin control spacing and the structural frame.

Screenshot of the Pencil Engraving Jig: 1. Pick a preset and measure

2. Set the text

  • Mode: Engrave & Print generates filled text for raster engraving and UV printing; Score generates single-pass vector text, much faster for big batches.
  • Type the Text and pick a Font; choose Alignment (Left, Center, Right) along the barrel and fine-tune with Text Size and Position Offset.
  • Auto-shrink long text keeps overlong names from running off the end instead of clipping.
  • Add an optional Symbol on the Left, Right, or Both ends of the text.

3. Export

Click Download SVG to get one file with Cut, Slots Cut, and Engrave layers. In Engrave & Print mode you can also Download Print PNG for UV flatbeds, and the STL/3MF section exports the jig as a printable tray with adjustable extrusion depth.

Screenshot of the Pencil Engraving Jig: 3. Export

Choose your build method

Laser Engraving

Cut the jig, engrave the batch

  1. Cut the jig sheet first: run the Slots Cut and Cut layers only, with the Engrave layer disabled.
  2. Without moving anything, tape the jig down and drop a pencil into each slot, all facing the same way with the same rotational position (logo or paint seam down).
  3. Run the Engrave layer only. The text lands centered on each barrel because jig and artwork share one coordinate system.
  4. Lift out the finished batch, reload, and run the engrave pass again. As long as the jig stays taped, registration holds all day.
  5. Use Score mode and a single-line font for the fastest cycle time on large orders.

UV Printing

Full-color barrels

  1. Cut or print the jig, then load it onto the UV flatbed with the blanks seated.
  2. Import the Print PNG at 1:1 scale and align it to the jig position in your RIP.
  3. Set the print height to the top of the barrel, not the jig surface; the curvature tolerates a couple of millimeters of focus range.
  4. Print. White ink underbase first on dark pencils, then color. UV gets you full-color designs that engraving cannot.

3D Printing

Print the jig instead

  1. No laser-safe sheet stock on hand? Export the STL or 3MF and set the extrusion depth (3-20 mm) for the tray thickness you want.
  2. Print flat in PLA at coarse layers; the jig is a fixture, not a showpiece.
  3. A printed jig has slightly grippier slot walls than plywood, which actually helps keep blanks from rotating.
  4. Use the printed jig on the laser bed or UV flatbed exactly like the cut version.

Next steps and project ideas

  • Classroom sets: every student's name on a pencil for the first day of school.
  • Drumstick pairs engraved with a band name make a fantastic gig merch item.
  • Wedding chopsticks with the couple's names and date as table favors.
  • Knitting needles labeled with their size near the head, a genuinely useful upgrade for knitters.
  • Mix names per slot by editing the text between batches while leaving the jig taped in place.
  • Engrave a motivational phrase along one side and a name on the other by flipping the blanks and running a second pass.
  • Use Score mode with a single-line font for an elegant handwritten look that engraves in seconds per pencil.

Take the design into your software

Was this guide helpful?