Making a summit keepsake with the Alpine Peak preset

Difficulty: Medium. Time: 2 to 3 hours. Best methods, in order: 3D printing (clean stepped summit), laser cutting, UV print.

This preset stacks nine summit contours from 2600 m to 4200 m into a hexagon on a dark slate backplate. It loads on the Matterhorn and is built for big-name peaks: the mountain someone climbed, skied, or proposed on.

Example of Alpine Peak
On this page (6)
  1. 1. Start from the preset
  2. 2. Tune the layers
  3. 3. Export
  4. 3D Printing
  5. Laser Cutting & Engraving
  6. UV & Sublimation Printing

What you need

3D printing

  • FDM printer; PLA in stone gray or white, or multicolor via 3MF
  • 3MF-capable slicer

Laser cutting

  • 9 thin sheets (1.5 to 3 mm laser-grade plywood or chipboard) for the contours + 1 backplate sheet (dark, #1f2937)
  • Laser cutter, glue, weights

UV print / sublimation

  • High-res PNG, hexagon or square blank

1. Start from the preset

Open the Alpine Peak preset. It loads centered on the Matterhorn at zoom 12.3: close enough that one massif fills the hexagon. Search your peak and keep zoom 12 to 13; center the actual summit, because the hexagon crop is unforgiving at the corners. Critical: the contour layers run 2600 to 4200 m in 200 m steps, tuned for 4000 m-class alpine peaks. For Rainier, Mont Blanc, or a 14er, shift the band up; for lower summits, shift it down (Step 2): otherwise most layers render empty.

Screenshot of the Alpine Peak: 1. Start from the preset

2. Tune the layers

Top to bottom:

  • Topography 4200m → 2600m: nine contour plates at 200 m intervals. Delete the ones above your summit, and confirm the lowest one still shows terrain at the hexagon edges.
  • Backplate: #1f2937 dark slate hexagon, the valley floor.

The nine contour layers default to stacked plates, but each (or the whole group, via Edit) now has a Score export type alongside Fill and Solid line: switch to Score to engrave the contour lines onto one sheet instead of cutting plates. The Topo Score Lines preset ships in that style.

3. Export

  • 3D printing: STL (single color, then dry-brush the summit white) or 3MF.
  • Laser: per-layer SVG ZIP; small-polygon cleanup on; high contours produce gnat-sized islands.
  • UV print: high-res PNG with everything visible; the contour tints carry the flat version.
Screenshot of the Alpine Peak: 3. Export

Choose your build method

3D Printing

3D printing

  1. Export and open in your slicer. The nine contours merge into a stepped summit pyramid on the hexagon plate.
  2. Print flat, no supports; 0.12 to 0.16 mm layers make the 200 m steps crisp.
  3. Scale 140 mm+ across flats so upper contours don't shrink to dots; export-time cleanup removes the hopeless slivers.
  4. Two-tone trick with a single extruder: filament swap to white at the contour that matches the snowline (~3400 m on the Matterhorn).

Laser Cutting & Engraving

Laser cutting

  1. Cut the Backplate hexagon from dark stock.
  2. Cut contours bottom-up, 2600 m to 4200 m, labelling each on the back.
  3. Dry-fit the nine-plate pyramid; nested summit contours only register one way.
  4. Glue bottom-up (or stack with 3M tape, 300LSE for ply or 467/468 for acrylic) weight, sand the hexagon edges flush, finish matte. Paint the top two or three plates white before assembly for permanent snow.

UV & Sublimation Printing

UV print / sublimation

  1. Export the high-res PNG: the contour tints over the dark backplate carry the design.
  2. Print on a hexagon acrylic blank or press onto white metal.

Next steps and project ideas

  • Built for icons: Matterhorn, Mont Blanc (shift band to 3000 to 4800 m), Rainier (2600 to 4400 m), Denali, your honeymoon volcano.
  • Climber's gift: add a route layer tracing the ascent line over the contours.
  • Snowline palette via 3MF: rock #6B6B6B below, white above the snowline.
  • Engrave the summit name, elevation, and the date of the climb on the backplate's visible margin.
  • Hanger hole ring + 100 mm hexagon = summit ornament for the tree.
  • Make the seven-summits set: same preset, seven peaks, one wall.
  • Swap the backplate to forest green #1E3B2E for treeline-and-rock contrast.

Take the design into your software

Was this guide helpful?