Turning photos into dot art with the Photo Halftone Generator

Difficulty: easy. Time: 10 to 20 minutes of design, plus machine time. Best methods, in order: laser engraving, 3D printing. Photos stay in your browser.

Halftone is the newspaper-photo trick: thousands of dots, each sized by how dark its patch of the image is, fuse into a portrait when you step back. This tool converts your photo into exactly that, as true vector circles rather than a dithered bitmap, so the dots cut and engrave perfectly at any scale. Everything processes locally; the photo never leaves your browser.

Engraved on wood or acrylic it reads as gallery-style pop art; printed in 3D it becomes a tactile raised-dot plaque whose image emerges from raking light.

Example of Photo Halftone Generator
On this page (5)
  1. 1. Upload and frame
  2. 2. Tune the dots
  3. 3. Export
  4. Laser Engraving & Cutting
  5. 3D Printing

What you need

1. Upload and frame

Open the tool and upload a photo. Faces and high-contrast subjects shine in halftone; flat, low-contrast images turn to mud. Use the Gamma, Brightness, and Contrast sliders to stretch the tonal range before worrying about dots.

2. Tune the dots

  • Width sets the physical size; halftones need viewing distance, so 150 mm is a practical minimum for faces.
  • Dot Pitch is the spacing of the grid; smaller pitch means more dots and more detail, but mind your machine's minimum feature size.
  • Max Dot Size caps how big the darkest dots grow; just over the pitch lets shadows fuse solid.
  • Pattern picks the grid: Square grid is classic print, Hexagonal packs smoother gradients, Jittered breaks the mechanical feel for an organic look.
  • Invert flips dark-dots-on-light to light-dots-on-dark; choose based on whether your process marks dark (wood engrave) or light (painted acrylic reveal).
  • Add cut frame appends a border rectangle so the panel cuts out in the same job.

3. Export

Download the SVG for laser work, or set Base Thickness and Dot Height and download the STL/3MF for a raised-dot plaque.

Choose your build method

Laser Engraving & Cutting

Engraving the halftone

  1. Import the SVG; the dots are filled vector circles, so raster-engrave them or, on small pitches, cut them clean through for a light-through panel.
  2. On plywood, engrave dots dark on the bare face; on painted or two-tone acrylic, engrave through the top color with Invert chosen to match.
  3. Run a 30 mm test square of the densest area to dial power before committing to the panel.
  4. Cut the frame border last.
  5. Step back three metres; halftones are judged from across the room, not on the bed.

3D Printing

Printing a raised-dot plaque

  1. Set Base Thickness around 2 to 3 mm and Dot Height 1 to 2 mm, then export the 3MF.
  2. Keep Dot Pitch at 2 mm or more so each dot is several extrusions wide.
  3. Print base-down with a 0.4 mm nozzle at 0.12 mm layers for clean dot tops.
  4. Swap to a contrast filament exactly at the base/dot boundary layer for a two-color image with zero painting.
  5. Hang it where side light rakes across the dots; the relief image pops hardest in angled light.

Next steps and project ideas

  • Engrave a wedding portrait halftone on a walnut panel for a fifth anniversary.
  • Pop-art pet portrait on white acrylic with Invert on, mounted on standoffs.
  • Cut the dots fully through thin plywood and backlight the panel with warm LEDs.
  • Band-poster style: halftone a concert photo and engrave it onto a clipboard or deck.
  • Print a tactile portrait plaque as a meaningful gift for a low-vision relative.
  • Hexagonal pattern plus jittered comparison: run the same photo both ways and pick by eye.
  • Halftone a city skyline as a long, narrow mantel piece.
  • Engrave onto leatherette for a halftone photo patch.

Take the design into your software

Was this guide helpful?