# Cutting maps on a Cricut > weed-able city street badges for HTV, decals, and stencils on a Cricut or Silhouette You do not need a laser to make a map. A Cricut (or Silhouette, or Brother ScanNCut) cuts the same map designer SVGs out of vinyl, so a city's street grid becomes a t-shirt badge, a tumbler wrap, a laptop decal, or a painted-wall stencil. The whole trick is exporting a design that stays in one connected piece on the cutting mat, so nothing tiny falls off and weeding stays sane. The [Vinyl T-Shirt Map preset](/map-designer?preset=vinyl-t-shirt-map) is purpose-built for this: it buffers every road into a contour and merges them with a border frame so the design exports as a single cuttable piece. The [Stylish Outline](/map-designer?preset=stylish-outline) and [Figure Ground Map](/map-designer?preset=figure-ground-map) presets also cut cleanly when you want a different look. ## What you need ### HTV / heat press (for fabric) - Heat transfer vinyl in one color (matte black looks great with the bold street design) - A blank t-shirt, hoodie, or canvas tote - A Cricut, Silhouette, or Brother ScanNCut; a heat press or household iron; a Teflon/parchment sheet - Weeding tools: a hook, tweezers, and good raking light ### Adhesive vinyl (for hard surfaces) - Permanent adhesive vinyl (Oracal 651 or similar), transfer tape, a squeegee - for tumblers, laptops, water bottles, car windows ## Step 1 - Frame a weed-friendly city Open [the Vinyl T-Shirt Map preset](/map-designer?preset=vinyl-t-shirt-map). It loads on a sample city with a hexagon export shape and a border frame everything connects to. Search your own city. - Zoom 11-12.5 works best: you want the *major* road skeleton, not every cul-de-sac. The more roads in frame, the more weeding. - Drag the map so a recognizable feature - a river bend, the downtown grid, a coastline - sits near the middle. That is what makes people say 'hey, that is my city.' - A river or lake helps: the Water layer punches it out as negative space, which reads beautifully on fabric. ## Step 2 - Keep the lines thick enough to weed **Roads** is a Cut-mode layer: every road is buffered into a contour and merged with the border frame so the whole design exports as *one connected piece*. That is exactly what a Cricut wants - nothing falls off the mat. **Width matters more than usual.** Stroke widths are relative to the design, so the physical line width depends on your final cut size. At a typical 250 mm chest print, the thinnest road tier comes out well under 1 mm wide - borderline to weed and prone to lifting in the wash. Two easy fixes: bump the smallest tier up to 3-4, or remove it entirely for a cleaner, bolder badge. Fewer, thicker roads always weed and wash better. **Water** is a Solid layer (a second vinyl color you layer behind the roads), or leave it off for a clean one-color decal. Turn on small-polygon cleanup if your city has lots of tiny ponds. ## Step 3 - Export for the cutter - Download the **combined SVG** (or the Roads layer SVG) - it is one merged outline Design Space / Silhouette Studio ingests directly. - For a one-color decal, cut just the Roads layer; for two-color, cut the Water shape from a second sheet and layer it behind. - Turn on **small-polygon cleanup** to remove slivers too small to weed. - Skip the mounting-hole options - they are for rigid materials, not vinyl. ## Vinyl Cutting (Cricut / Silhouette) ### HTV on a shirt or tote 1. Import the SVG into Design Space (or Silhouette Studio) and size it: 220-260 mm wide suits an adult medium chest. 2. **Mirror the design horizontally** - HTV cuts from the back. This is the step everyone forgets exactly once. 3. Load HTV shiny-side (carrier) down. Run a test cut first; you want a kiss-cut through the vinyl, not the carrier. 4. Weed: remove everything *except* the roads and frame. Start from the outside, work inward, pull slowly so thin roads stay anchored. Raking light makes the cut lines pop. 5. Pre-press the shirt 5 seconds, position the design (center it ~7-8 cm below the collar), and press per your vinyl's spec (typically ~150 C / 305 F, 10-15 s, medium pressure). 6. Peel the carrier (hot or cold per the vinyl), cover with parchment, and give it a 5-second second press to lock the fine roads down. Care note: wash inside-out, cold, no dryer heat - the finest roads are the first thing to lift if you cook them. ### Adhesive vinyl on a tumbler, laptop, or wall 1. Cut the same SVG **not mirrored** on permanent adhesive vinyl. 2. Weed as above, then lay transfer tape over the design and burnish well - the frame holds everything in register. 3. Apply to a clean surface; squeegee firmly, then peel the tape back at a sharp angle. For curved tumblers, size the design narrow and apply slowly. 4. Stencil variant: cut the design in stencil vinyl, weed out the roads (the reverse of HTV), and use it as a paint mask for a wood sign. ## Make it yours - Swap the hexagon for a circle or heart export shape - the Cut-mode frame adapts automatically. - Two-city design: cut two smaller shapes side by side ('where we met / where we live'). - Drop the smallest road tier and bump the motorways thicker for a chunky badge that weeds in five minutes. - Metallic, glitter, or flock HTV turns the street grid into a statement piece. - Zoom to 14 and let one neighborhood's grid fill the shape instead of the whole city. - Pair with a text layer of the city's coordinates cut in a second color beneath the map. --- Open the Vinyl T-Shirt Map preset: https://www.mylasertools.com/map-designer?preset=vinyl-t-shirt-map Read online: https://www.mylasertools.com/learn/guides/cutting-maps-on-cricut